Retro GEM PS2 Fat Installation: Difference between revisions
| Line 142: | Line 142: | ||
Solder the adapter flex to the main flex. Do not bridge the 3V3 Jumper (circle in purple) if you have a GH-015. | Solder the adapter flex to the main flex. Do not bridge the 3V3 Jumper (circle in purple) if you have a GH-015. | ||
[[File:FLEXADAP_SMALL.JPG|500px]] | [[File:FLEXADAP_SMALL.JPG|500px]] | ||
You will need to solder some extra wires as compared to the other fat installations. CLK, VSYNC, HSYNC, GND, 1.8V (GH-015 Only) | You will need to solder some extra wires as compared to the other fat installations. CLK, VSYNC, HSYNC, GND, 1.8V (GH-015 Only) | ||
| Line 148: | Line 148: | ||
Refer to the the pinout images and follow the hookups below. | Refer to the the pinout images and follow the hookups below. | ||
[[File:GH15_PINOUT_SMALL.JPG|500px]] | [[File:GH15_PINOUT_SMALL.JPG|500px]] | ||
[[File:30KGH15_SMALL.JPG|500px]] | [[File:30KGH15_SMALL.JPG|500px]] | ||
Solder the first arm. | Solder the first arm. | ||
[[File:GH15_FINGER1_SMALL.JPG|500px]] | [[File:GH15_FINGER1_SMALL.JPG|500px]] | ||
Solder the second arm. | Solder the second arm. | ||
[[File:GH15_FINGER2_SMALL.JPG|500px]] | [[File:GH15_FINGER2_SMALL.JPG|500px]] | ||
Flip the flex as shown. | Flip the flex as shown. | ||
[[File:GH15_FLIP_SMALL.JPG|500px]] | [[File:GH15_FLIP_SMALL.JPG|500px]] | ||
Solder the last arm, this can be challenging. | Solder the last arm, this can be challenging. | ||
[[File:GH15_FINGER3_SMALL.JPG|500px]] | [[File:GH15_FINGER3_SMALL.JPG|500px]] | ||
Tape down the flex and solder the audio arm. | Tape down the flex and solder the audio arm. | ||
[[File:GH15_AUD_SMALL.JPG|500px]] | [[File:GH15_AUD_SMALL.JPG|500px]] | ||
Remove some of the solder mask for the GND layer and solder the flex cable down as shown. | Remove some of the solder mask for the GND layer and solder the flex cable down as shown. | ||
[[File:GH15_GND_SMALL.JPG|500px]] | [[File:GH15_GND_SMALL.JPG|500px]] | ||
Hookup the rest of wires, 1V8, 5V, 3V3, CLK, HSYNC and VSYNC. Use 30AWG or smaller wire for the CLK/HSYNC/VSYNC | Hookup the rest of wires, 1V8, 5V, 3V3, CLK, HSYNC and VSYNC. Use 30AWG or smaller wire for the CLK/HSYNC/VSYNC | ||
| Line 180: | Line 180: | ||
PAY EXTREMELY close attention to the 1V8 hook up on the flex. It is only connected to one side of the 3v3 jumper circled earlier. | PAY EXTREMELY close attention to the 1V8 hook up on the flex. It is only connected to one side of the 3v3 jumper circled earlier. | ||
[[File:GH15_HOOKUP2_SMALL.JPG|500px]] | [[File:GH15_HOOKUP2_SMALL.JPG|500px]] | ||
== Installing the controller hookup == | == Installing the controller hookup == | ||