Retro GEM GC Installation: Difference between revisions
| (8 intermediate revisions by the same user not shown) | |||
| Line 15: | Line 15: | ||
The doc assumes you are doing a no cut (Replace analog or digital port) installation in your GameCube. | The doc assumes you are doing a no cut (Replace analog or digital port) installation in your GameCube. | ||
If you are upgrading an existing GCDual or other installation and wanting to do the case cut you will need the 3D printed spacer to mount. | If you are upgrading an existing GCDual or other installation and wanting to do the case cut you will need the 3D printed spacer [[https://docs.pixelfx.co/GEM_PRINTS/GCDUAL_MOUNT.stl]] to mount. | ||
Blueshell3D has created a very nice [[https://www.printables.com/model/1244072-gamecube-replacement-rear-io-panels-for-retrogem:3D printed backplate]] that allows for full-size HDMI in the GCDual cut location. This is a great option for people wanting to keep both ports while keeping full size HDMI at the same time. | Blueshell3D has created a very nice [[https://www.printables.com/model/1244072-gamecube-replacement-rear-io-panels-for-retrogem:3D printed backplate]] that allows for full-size HDMI in the GCDual cut location. This is a great option for people wanting to keep both ports while keeping full size HDMI at the same time. | ||
| Line 36: | Line 35: | ||
=== Items Required === | === Items Required === | ||
* Temperature Controlled Soldering Iron | |||
* Leaded Solder | |||
* Non-Corrosive, No Clean Flux (Amtech 559 / Kester 959T) | |||
* 99% Isopropyl Alcohol | |||
* Multi Meter | |||
* Exacto Knife | |||
* Small screw Phillips screw drivers | |||
* Side cutters | |||
== GEM Jumpers == | |||
== Disassembly == | |||
== Installation == | |||
=== HDMI Mount === | |||
==== No Cut Mounting ==== | |||
==== Cut Mounting ==== | |||
=== PCB Mount === | |||
=== Flex Installation === | |||
==== DOL-001 ==== | |||
==== DOL-101 ==== | |||
=== Mounting the GEM === | |||
=== HDMI FFC === | |||
=== Reassembly === | |||
== First Bootup == | |||
Latest revision as of 21:11, 17 December 2025
Place Holder
Introduction
Disclaimer
Disclaimer: This kit is for advanced installers only. Install at your own risk. We cannot be held responsible for damage to your console and/or kit.
Important Information
The kit is compatible with both DOL-001 and DOL-101
While the kit will work with the Panasonic Q its not outlined in the this guide. Make sure to grab Jesusburnsneon's [adapter] if you are doing a Q.
The doc assumes you are doing a no cut (Replace analog or digital port) installation in your GameCube.
If you are upgrading an existing GCDual or other installation and wanting to do the case cut you will need the 3D printed spacer [[1]] to mount.
Blueshell3D has created a very nice [printed backplate] that allows for full-size HDMI in the GCDual cut location. This is a great option for people wanting to keep both ports while keeping full size HDMI at the same time.
Kit Contents
- GC Main Flex
- Full Size HDMI Adapter Board
- Male HDMI Adapter
- 150mm 18p FFC Cable
- FR4 Mount
- M1.6 Screw mount (2x)
- M1.6 Screw 3mm (2x)
- Wifi Antenna
- M2 Screw
- M2 Nut
- Plastic HDMI mount
Items Required
- Temperature Controlled Soldering Iron
- Leaded Solder
- Non-Corrosive, No Clean Flux (Amtech 559 / Kester 959T)
- 99% Isopropyl Alcohol
- Multi Meter
- Exacto Knife
- Small screw Phillips screw drivers
- Side cutters