Retro GEM Wii Installation: Difference between revisions

(3 intermediate revisions by 2 users not shown)

Line 28:

Here is a video installation of a 4 layer board. Please use it for references and techniques.

https://youtu.be/231tQfbZO_k

<youtube>231tQfbZO_k</youtube>

=== Kit Contents ===

Line 65:

Line 66:

Retro GEM jumper information Tool

https://docs.pixelfx.co/fxdigital-config.html

https://docs.pixelfx.co/fxdigital-config.html?c=wii

== Disassembly ==

Line 168:

Line 169:

=== Case Cut ===

Part of the top case must be trimmed for the Mini HDMI to clear. Just small cut and file is needed.

Part of the top case must be trimmed for the Mini HDMI to clear. Just small cut and file as needed.

[[File:WII_CUT.jpeg|500px]]

Line 202:

Line 203:

Solder the GEM PCB mount and install the supplied M1.6 mounts

*Pay careful attention to not put the PCB MOUNT on top of any components on the Wii PCB. There is a small resistor pack can be shorted without careful attention to this area. If this resistor pack is shorted, it must be ~~<a href="~~https://www.digikey.de/en/products/detail/panasonic-electronic-components/EXB-28V101JX/256275~~">replaced</a>~~. More details can be found on the discord here: https://discord.com/channels/1101136714916962364/1425610417505570959/1435257770441183376 *

*Pay careful attention to not put the PCB MOUNT on top of any components on the Wii PCB. There is a small resistor pack can be shorted without careful attention to this area. If this resistor pack is shorted, it must be replaced [https://www.digikey.de/en/products/detail/panasonic-electronic-components/EXB-28V101JX/256275 Link to Replacement resistor pack]. More details can be found on the discord here: https://discord.com/channels/1101136714916962364/1425610417505570959/1435257770441183376 *

[[File:RA20.png|500px]]

@@ Line 28: / Line 28: @@
 Here is a video installation of a 4 layer board. Please use it for references and techniques.
-https://youtu.be/231tQfbZO_k
+<!-- embedded video link for https://youtu.be/231tQfbZO_k -->
+<youtube>231tQfbZO_k</youtube>
 === Kit Contents ===
@@ Line 65: / Line 66: @@
 Retro GEM jumper information Tool
-https://docs.pixelfx.co/fxdigital-config.html
+https://docs.pixelfx.co/fxdigital-config.html?c=wii
 == Disassembly ==
@@ Line 168: / Line 169: @@
 === Case Cut ===
-Part of the top case must be trimmed for the Mini HDMI to clear. Just small cut and file is needed.
+Part of the top case must be trimmed for the Mini HDMI to clear. Just small cut and file as needed.
 [[File:WII_CUT.jpeg|500px]]
@@ Line 202: / Line 203: @@
 Solder the GEM PCB mount and install the supplied M1.6 mounts
-*Pay careful attention to not put the PCB MOUNT on top of any components on the Wii PCB. There is a small resistor pack can be shorted without careful attention to this area. If this resistor pack is shorted, it must be <a href="https://www.digikey.de/en/products/detail/panasonic-electronic-components/EXB-28V101JX/256275">replaced</a>. More details can be found on the discord here: https://discord.com/channels/1101136714916962364/1425610417505570959/1435257770441183376 *
+*Pay careful attention to not put the PCB MOUNT on top of any components on the Wii PCB. There is a small resistor pack can be shorted without careful attention to this area. If this resistor pack is shorted, it must be replaced [https://www.digikey.de/en/products/detail/panasonic-electronic-components/EXB-28V101JX/256275 Link to Replacement resistor pack]. More details can be found on the discord here: https://discord.com/channels/1101136714916962364/1425610417505570959/1435257770441183376 *
 [[File:RA20.png|500px]]